Exterior View
Product Specs
General Specifications
- Maximum Rating
- 2500 BHP
- Displacement
- 3596 in³
- Minimum Rating
- 2250 BHP
- Aspiration
- SCAC and ATAAC
- Flywheel and Flywheel Housing
- SAE No. 0
- Flywheel Teeth
- 151
- Stroke
- 8.5 in
- Bore
- 6.7 in
- Governor and Protection
- Electronic (ADEM™ A5) / DGB System (ADEM™ A6)
- Rotation from Flywheel End
- Counterclockwise
Emissions
- Emissions
- U.S. EPA Tier 4 Final
Dimensions
- Length
- 137.4 in
- Width
- 88 in
- Height
- 107 in
- Weight
- 22657 lb
Capacity for Liquids
- Lube Oil System - Refill
- 52 gal (US)
- Cooling System
- 52 gal (US)
Standard Equipment
-
- Control System
-
- Cat ADEM A6 DGB controls
-
- Cooling System
-
- Thermostats and housing, jacket and separate circuit water pump, gear-driven centrifugal
- SCAC/ATAAC system
-
- Exhaust System
-
- Dual DOC
- Exhaust manifold, dry, bellows connection
- Four turbochargers with watercooled bearings
- Exhaust outlet, dual 10-inch ANSI round flange as part of aftertreatment
-
- Flywheels & Flywheel Housing
-
- Flywheel, SAE No. 0, 151 teeth
-
- Fuel System
-
- Engine mounted Gas filter, water coalescing type
- Clean fuel module boost pump
- Fuel transfer pump
- Common rail fuel system
- Primary/secondary fuel filters
- Fuel priming pump (electric)
-
- Instrumentation
-
- Product LinkTM engine monitoring
-
- General
-
- Vibration damper and guard
- Lifting eyes
- Paint - Caterpillar yellow
-
- Lube System
-
- Closed Crankcase ventillation - top mounted
- Fumes disposal
- Oil filter - RH spin-on type
- Oil cooler
- Oil filler and dipstick - LH
- Oil scavenger pump
- Oil pump
- Oil pan drain valve, 1" NPT female connection
-
- Mounting System
-
- Trunion front support
- Flywheel housing - two-sidedfailure options
-
- Protection System
-
- Emergency stop logic inputs provided at 70-pin customer interface connection
- ADEM A5 and A6 ECU system to provide customer programmable engine deration strategies to protect against adverse operating conditions
-
- Aftertreatment Mounting
-
- CEM/muffler support package Heavy-duty air cleaners (2 element with precleaners)
Attachments
-
- Charging System
-
- 80, 95, or 150 amp charging alternator
-
- Control System
-
- Local speed throttle control
- Throttle position sensors
-
- Cooling System
-
- Coolant conditioner
- JW outlet coupling-style connections
- JW inlet weld-flange connection
- SCAC/ATAAC inlet and outlet coupling-style connections
- JW inlet and outlet hose barb connections
- SCAC/ATAAC inlet and outlet hose barb connections Water level switch gauge
- JW Heater installation connections
-
- Exhaust System
-
- Flex pipe kit
- Residential mufflers (painted steel and stainless steel) with outlet elbow and rain cap
-
- Flywheels & Flywheel Housing
-
- Allison and Twin Disc flywheel options
-
- Instrumentation
-
- Product Link harness extensions
- LAN adapters
-
- Lube System
-
- Rear sump oil pan - 250-hour change interval
- Front deep sump oil pan - 500-hour change interval
-
- Power Take-offs
-
- Front Crankshaft Adapter
- Front crankshaft stub shaft
- Accessory drive - upper RH
-
- Protection System
-
- Hydraulic actuated air shutoff
-
- Starting System
-
- Dual hydraulic starter - LH
- Manual engine barring device
- Hydraulic starter - LH
- EIRS automatic start/stop system is available on factory orders as an attachment
-
- Transmission Attachments
-
- Transmission oil cooler
- Transmission oil cooler 2-1 connections
- Torque converter connections
-
- General
-
- Air compressor