Product Specs
Power Rating
- Minimum Rating
- 400 BHP
- Maximum Rating
- 1333 BHP
Engine Specifications
- Aspiration
- Turbocharged-aftercooled
- Emissions
- U.S. EPA Tier 4 Final certified, IMO III emissions certified (SCR required)
- Rotation
- Counterclockwise from flywheel end
- Bore
- 5.71 in
- Configuration
- Vee 12, 4-stroke-cycle diesel
- Stroke
- 6.38 in
- Displacement
- 1959 in³
- Oil Change Interval
- 750 hrs - deep pan
- Rated Engine Speed
- 1800 rpm
- Governor
- Electronic (A5 ECM)
- Refill Capacity
- Lube Oil System w/ oil filter change: 146 L (38.5 gal) - deep pan
- Cooling
- Heat exchanger or keel cooled
- Flywheel Housing
- SAE No. 0 with SAE No. 18 flywheel (136 teeth)
Dimensions & Weights
- Maximum Width
- 57.3 in
- Maximum Height
- 63.5 in
- Maximum Engine Dry Weight
- 7160 lb
- Minimum Engine Dry Weight
- 6950 lb
- Minimum Length
- 83.9 in
- Maximum Length
- 89.8 in
- Minimum Width
- 57.1 in
- Minimum Height
- 59.3 in
Clean Emissions Module (CEM) - Dimensions
- 6 Brick U-Flow - Length
- 85 in
- 6 Brick Z-Flow - Weight
- 1246 lb
- 6 Brick Z-Flow - Width
- 43.5 in
- Dosing Cabinet - Length
- 37.4 in
- Dosing Cabinet - Width
- 18.8 in
- 6 Brick U-Flow - Height
- 23.5 in
- 6 Brick Z-Flow - Height
- 23.5 in
- 6 Brick U-Flow - Weight
- 1235 lb
- Dosing Cabinet - Weight
- 209 lb
- 6 Brick U-Flow - Width
- 56.9 in
- 6 Brick Z-Flow - Length
- 147.7 in
- Dosing Cabinet - Height
- 22.8 in
Standard Equipment
-
- Air Inlet System
-
- Separate circuit aftercooled (SCAC)
- Closed crankcase fumes disposal
-
- Control System
-
- 24V control system
-
- Cooling System
-
- Heat exchanger or Keel Cooling
- Watercooled exhaust manifold and turbocharger
- Hard seawater lines – no flexible hoses
- Flanges for cooling connections, ANSI or DIN
-
- Fuel System
-
- Duplex fuel filters with hybrid fuel lines
- Shipped loose primary fuel filter with water separator
- Fuel transfer and priming pump
-
- Lube System
-
- Oil fill, simplex filter and dipstick
- Deep or shallow sump oil pan
-
- Mounting System
-
- Adjustable front support mounting system
-
- General
-
- Right or left hand service sides
- Customer wiring and service tool connector
Attachments
-
- Alarm And Protection
-
- MECP I control panel
- MECP III control panel with Cat® Alarm and Protection System
-
- Exhaust System
-
- Water-in-fuel and exhaust temperature sensors
- Muffler
-
- Charging System
-
- Charging alternator
-
- Fuel System
-
- Manual or electric fuel priming pump
- Fuel cooler
-
- Lube System
-
- Duplex oil filters
-
- Power Take-offs
-
- Front drives including stub shaft and pump drive
- Rear SAE A or B pump drives
-
- Starting System
-
- Starting motors – air, electric or redundant