Product Specs
Generator Set Specifications
- Minimum Rating
- 282 ekW
- Maximum Rating
- 940 ekW
- Frequency
- 60hz
Engine Specifications
- Configuration
- Vee-12, 4-stroke-Cycle-Diesel
- Aspiration
- Turbocharged-aftercooled aspiration
- Bore
- 5.71 in
- Stroke
- 6.38 in
- Displacement
- 1959 in³
- Emissions
- U.S. EPA Tier 4 Final certified / IMO III emissions certified (SCR required)
- Rated Engine Speed
- 1800 rpm
- Governor
- Electronic (A5 ECM)
- Generator
- SR5 - Form Wound
- Cooling
- Heat exchanger, keel or radiator cooled
- Oil Change Interval
- 750 hrs
- Refill Capacity
- Lube Oil System w/ oil filter change: 146 L (38.5 gal)
Generator Set Dimensions
- Length
- 167.2 in/4245 mm (minimum), 226.1 in/5742 mm (maximum)
- Width
- 59.9 in/1521 mm (minimum), 89.8 in/2280 mm (maximum)
- Height
- 70.4 in/1747 mm (minimum), 92.8 in/2356 mm (maximum)
- Engine Dry Weight
- 15721 lb/7131 kg (minimum), 21998 lb/9978 kg (maximum)
Clean Emissions Module (CEM) - Dimensions
- 6 Brick Z-Flow - Length
- 147.7 in
- Dosing Cabinet - Weight
- 209 lb
- 6 Brick Z-Flow - Weight
- 1246 lb
- 6 Brick U-Flow - Weight
- 1235 lb
- Dosing Cabinet - Height
- 22.8 in
- 6 Brick U-Flow - Width
- 56.9 in
- 6 Brick U-Flow - Length
- 85 in
- Dosing Cabinet - Width
- 18.8 in
- 6 Brick Z-Flow - Width
- 43.5 in
- 6 Brick U-Flow - Height
- 23.5 in
- Dosing Cabinet - Length
- 37.4 in
- 6 Brick Z-Flow - Height
- 23.5 in
Standard Equipment
-
- Air Inlet System
-
- Separate circuit aftercooled (SCAC)
- Closed crankcase fumes disposal
-
- Control System
-
- 24V control system
-
- Cooling System
-
- Heat exchanger or Keel Cooling
- Watercooled exhaust manifold and turbocharger
- Hard seawater lines – no flexible hoses
- Flanges for cooling connections, ANSI or DIN
-
- Fuel System
-
- Duplex fuel filters with hybrid fuel lines
- Primary fuel filter with water separator installed on base frame
-
- Generators And Generator Attachments
-
- IP23, air cooled, form wound SR5 generator offered in 440, 480 and 690V
-
- Lube System
-
- Oil fill, simplex filter and dipstick
-
- Mounting System
-
- Helical spring/rubber isolated mounting for vibration and structure borne noise reduction
-
- General
-
- Right or left hand service sides
- Customer wiring and service tool connector
Attachments
-
- Alarm And Protection
-
- MGCP III B control panel with Cat® Alarm and Protection System
- IP44 generator protection
-
- Exhaust System
-
- Muffler
- Water-in-fuel and exhaust temperature sensors
- SOLAS approved spray shielding
-
- Charging System
-
- Charging alternator
-
- Fuel System
-
- Manual or electric fuel priming pump
- Fuel cooler
-
- Lube System
-
- Duplex oil filters
-
- Starting System
-
- Starting motors – air, electric or redundant